Dimensions
Wrench sizes follow ISO 4014 / ISO 4017. Older DIN 931 / DIN 933 bolts differ at several sizes (M10 = 17, M12 = 19, M14 = 22, M22 = 32) - check the bolt before choosing a spanner.
ISO 273 clearance holes (fine / medium / coarse).
M48 × 5.0 in numbers
M48 × 5.0 is 48 mm across the crests with a 5 mm pitch, which is 5.1 threads per inch. The basic pitch diameter is 44.753 mm and the bolt's minor diameter 41.866 mm, so the thread is 3.067 mm deep on the bolt. The nearest inch size, 2-4.5 UNC, is 2.80 mm larger across the crests and its pitch is 0.644 mm coarser, so the two do not interchange.
Tap drill by thread percentage
Hole = D − % × 0.0129904 × P, with D = 48 mm and P = 5 mm. A smaller hole leaves more thread; the recommended 43 mm drill above gives about 77%.
Tightening torque estimate
Target preload is 75% of proof load; torque is estimated from T = K · F · d.
Strengths are ISO 898-1:2013 Table 3 for d > 16 mm. Class 8.8 is size-banded - 580 MPa proof at or below 16 mm, 600 MPa above - while 10.9 and 12.9 hold one value across the range. ISO 898-1's tabulated range stops at M39; above that the same class values apply only by agreement between supplier and purchaser.
These figures assume a nut factor of K = 0.20 (dry / as-received steel). K captures thread and head friction and can swing torque by 30% or more - a lubricated joint needs noticeably less. Change the lubrication assumption in the bolt-torque calculator. Put M48 × 5.0 on a job sheet
The bolt schedule collects the fasteners for one job onto a single sheet - tap drill, wrench size, grade and tightening torque on every line, taken straight from pages like this one. Free schedules hold 3 lines and are saved in this browser only.
What tap drill do I need for M48 × 5.0?
For a M48 × 5.0 thread, drill the hole with a 43 mm tap drill (43 mm - the standard D − P rule) before tapping. That produces roughly 77% thread engagement, the usual target for a strong, tappable hole. The mating bolt has a major diameter of 48 mm and a pitch of 5 mm (≈5.08 TPI (converted)).
To pass a M48 × 5.0 bolt through a part rather than thread it, use a clearance hole: Close 50 · Normal 52 · Loose 56 mm.
All values come from the standard thread formulas (ISO 68-1 / ASME B1.1) and published standard tables. See the full reference.
Frequently asked questions
What drill size do I need to tap a M48 × 5.0 thread?
Drill 43 mm before tapping M48 × 5.0. That leaves roughly 77% thread engagement, the usual target for a strong hole that still taps cleanly.
Is M48 × 5.0 a coarse or fine thread?
M48 × 5.0 is a metric coarse thread. Coarse is the default pitch for M48: when a drawing or supplier says just M48, it means this 5 mm pitch.
What size clearance hole does a M48 × 5.0 bolt need?
Drill 50 mm for a close fit, 52 mm for a normal fit or 56 mm for a loose fit (ISO 273). A clearance hole lets the M48 × 5.0 bolt pass through the part instead of threading into it.
How much torque should I use on a M48 × 5.0 bolt?
Estimated tightening torque for M48 × 5.0 runs from 6364 N·m (Class 8.8) to 10288 N·m (Class 12.9), targeting 75% of proof load with a dry nut factor of K = 0.20. Lubricated threads need noticeably less torque.