Dimensions
Cross-check: the standard plain-end weight formula W = 10.6802 x t x (OD - t) gives 238.35 lb/ft here, 0.1% from the published 238.57 lb/ft. The published figure is the one printed above.
NPS 24 schedule 60 in numbers
NPS 24 schedule 60 pipe measures 24.000 in (609.60 mm) across the outside with a 0.969 in wall, so the bore is 22.062 in (560.38 mm). That bore gives a flow area of 382.3 in² and holds 19.86 US gallons per foot (246.6 litres per metre). The outside diameter is 24.8 times the wall, and the steel itself has a cross-section of 70.11 in² and weighs 238.57 lb per foot plain end.
Schedule 40 is the next lighter wall at NPS 24: 0.688 in, 0.281 in thinner, which opens the bore to 22.624 in and adds 5.2% to the flow area, for 28% less weight per foot.
Schedule 80 is the next heavier wall at NPS 24: 1.219 in, 0.250 in thicker, which narrows the bore to 21.562 in and cuts 4.5% from the flow area, for 24% more weight per foot.
Worked out from the dimensions
Plain geometry of a hollow circle with OD = 24.000 in and ID = 22.062 in: flow area π/4·ID², metal area π/4·(OD² − ID²), moment of inertia π/64·(OD⁴ − ID⁴), section modulus I ÷ (OD/2), radius of gyration √(I ÷ metal area), capacity flow area × 12 ÷ 231 (231 in³ to the US gallon). Nominal dimensions, so mill tolerance and corrosion allowance are not included.
Why 24 inch pipe is not 24 inches
Nominal Pipe Size is a label, not a measurement. NPS 24 pipe has an outside diameter of 24.000 inches, and it keeps that outside diameter in every schedule made. What the schedule number changes is the wall: at schedule 60 the wall is 0.969 inches, so the bore comes out at 22.062 inches.
That is the practical consequence. Fittings, flanges, supports and threading dies are sized to the outside diameter, so they fit any schedule of the same trade size. Flow, pressure drop and anything that has to pass through the pipe depend on the inside diameter, which changes with every schedule. Order by trade size and schedule; work your hydraulics from the bore.
Other schedules in NPS 24
Same outside diameter of 24.000 inches throughout - only the wall and the bore move.
Frequently asked questions
What is the wall thickness of 24 inch schedule 60 pipe?
0.969 inches (24.61 mm). The outside diameter is 24.000 inches (609.60 mm) whatever the schedule, so this wall leaves an inside diameter of 22.062 inches.
What is the inside diameter of 24 inch schedule 60 pipe?
22.062 inches (560.38 mm). Inside diameter is outside diameter minus twice the wall: 24.000 - 2 x 0.969 = 22.062 inches.
Is 24 inch pipe actually 24 inches?
No. NPS 24 is a trade size, not a measurement. The pipe measures 24.000 inches across the outside and 22.062 inches across the bore in this schedule. Only the outside diameter is fixed across schedules.
How much does 24 inch schedule 60 pipe weigh?
238.57 pounds per foot plain end (355.28 kg per metre), for carbon steel. The figure excludes coatings, linings and fittings.
Where this table stops
This table runs from NPS 1/8 to NPS 24 and stops there. ASME B36.10M itself continues to NPS 80; those larger sizes are not carried here, so a size above NPS 24 is missing rather than undefined.
Where these figures come from
Dimensions are as defined by ASME B36.10M (welded and seamless wrought steel pipe). This site is an independent reference and is not affiliated with, endorsed by or approved by any standards body.
Every value on this page was cross-checked against 4 independent published sources:
Sources disagree here. Published tables split on the last digit here - 0.969 in (b3610m-fbc), 0.968 in (b3610m-wikipedia); 24.61 mm (b3610m-ferrobend), 24.61 mm (b3610m-wermac), 24.59 mm (b3610m-wikipedia). The figure printed is 0.969 in (24.61 mm), carried by the majority of the sources. The two readings describe the same wall: they differ by less than a thousandth of an inch, far inside the mill tolerance of minus 12.5 percent on wall thickness.
Last-digit inch walls across the whole table: 0.594, 0.688, 0.719, 0.844, 0.938, 1.094, 1.219, 1.438, 1.969, 2.344 in (b3610m-fbc) against 0.593, 0.687, 0.718, 0.843, 0.937, 1.093, 1.218, 1.437, 1.968, 2.343 in (b3610m-wikipedia). Two families of inch figures are in circulation, one a thousandth of an inch below the other, and they come from rounding the millimetre wall the standard tabulates rather than from any difference in the pipe. The higher family is what the majority of the sources read here carry and is what this site prints; the affected rows say so individually. Nothing turns on the choice: the wall tolerance is minus 12.5 percent, which at a half-inch wall is sixty times the gap.
NPS 14 extra strong (XS): 0.469 in (b3610m-fbc) against 0.500 in (b3610m-etb) against 0.500 in (b3610m-wikipedia). 0.500 in is printed here. Two of the three inch sources give it, both millimetre sources give 12.70 mm which is 0.500 in, and extra strong is a 0.500 in wall at every size from NPS 12 up. The 0.469 in reading looks like a misplaced row in that one chart, but it is recorded rather than deleted.